Jul 13, 2016 This item Sony ICFC1PJ Alarm Clock Radio. Sony ICFC1TBLACK Alarm Clock Radio, Black. New & Improved - Sony Projector Dual Alarm Clock with Extendable Snooze, 5 Nature Sounds, AM/FM Radio, Built-in Calendar, Large LED Display & USB Port (Black) + 2 Sony Rplc. User Manual pdf Warranty pdf. This item Sony ICFC1PJ Alarm Clock Radio Sony ICFC1TBLACK Alarm Clock Radio, Black New & Improved - Sony Projector Dual Alarm Clock with Extendable Snooze, 5 Nature Sounds, AM/FM Radio, Built-in Calendar, Large LED Display & USB Port (Black) + 2 Sony Rplc.
Page 2: Listening to the radio, Selecting a nature sound, Setting the alarm, Setting the sleep timer, Setting the brightness of the display, Charging a smartphone
Advertising
ICF-C1PJ_U2 [US] 4-528-478-
11(2)
Display
Projector unit
Projector lens
NATURE SOUND/PRESET
AC power cord
FM wire antenna
Use the tactile dots on
VOL/SET + and TUNING + and the tactile characters on 3
(
NATURE SOUND/PRESET) and ALARM RESET/OFF as a guide when operating the
unit.
Operations
Setting the clock
manually
To change the clock setting manually, operate
the unit as follows.
1
Press and hold
SET TIME/DATE for
more than 2 seconds.
The year will start to flash on the display.
2
Press
VOL/SET + or – repeatedly to
select the year, and then press
SNOOZE/BRIGHTNESS/ENTER.
3
Repeat step
2 to set the month, day
and time.
After setting the time, a beep will sound.
Notes
If you do not press any button for about 1
minute while setting the clock, clock setting
mode will be canceled.
A 100-year calendar (2013 - 2112) is installed
in the system.
To change the time format
You can choose between the 12-hour system
(default) or the 24-hour system to display the time.
Press and hold
ALARM RESET/OFF and
SNOOZE/BRIGHTNESS/ENTER for about
3 seconds.
The time format toggles between the 12-hour
system (“AM 12:00” = midnight) and the 24-hour system (“0:00” = midnight).
To display the date and year
Press
SET TIME/DATE once to display the
month and day, and press again to display the
year. To return to the current time display, press SET TIME/DATE once again; or after a few seconds the clock display will return automatically.
When daylight saving time
(summer time) begins/ends
while Automatic DST/summer
time adjustment is set to off
Change the clock setting manually if you have
canceled the Automatic DST/summer time adjustment.
Using the projector
The projector function allows you to display the
clock and the currently used alarm icons on a nearby wall or ceiling at a range of 0.5 m – 4 m (1 5/8 feet – 13 1/8 feet).
1
Rotate the projector unit to point the
projector lens in the desired direction.
2
Press
PROJECTION.
3
Turn
FOCUS to adjust the focus.
To turn off the projector, press
PROJECTION
again.
To rotate the projection view
Press
ROTATEPROJECTION repeatedly.
Each time you press
ROTATEPROJECTION, the
projection view rotates as Fig.
.
Notes
Do not stare into the lens directly.
The projector function cannot be used unless
the clock has been set.
Certain walls and ceilings may not display
the projection properly.
The projector unit can be rotated 90° forward
or backward from the upward position, and
clicks when returned to the upward position.
If the projector unit is rotated beyond its
limits, it may be damaged.
The projector will automatically turn off after
16 hours.
Listening to the radio
1
Press
AM/FM/NATURE SOUND
repeatedly to select the desired band
(
AM or FM).
2
Press
TUNING + or – to tune to the
desired station.
If you press and hold
TUNING + or –,
scanning starts. Scanning pauses when a
station is found, and restarts after a few seconds. To stop scanning, press
TUNING +
or
– (or SNOOZE/BRIGHTNESS/ENTER).
3
Press
VOL/SET + or – to adjust the
volume.
To turn off the radio, press
ALARM RESET/
OFF.
To preset radio stations
You can preset 5 stations for FM and 5 stations
for AM.
1
Tune to the station you wish to preset.
2
Press and hold the desired
NATURE
SOUND/PRESET (1 to 5) until you hear
a beep.
Example: The following display appears
when you preset FM 105.7 MHz to preset number 3 for FM.
The display shows the frequency for a few
seconds and then changes back to the current time. To change the preset station, tune to the desired station and press and hold the NATURE SOUND/PRESET (1 to 5) until you hear a beep.
Note
If you try to store another station with the
same preset number, the previously stored
station will be replaced.
To tune to a preset station
1
Press
My flash usb stick has no connection to my Acer Aspire notbook. Any suggestions?Answer: Check the device manager if the device is yellow marked. Acer's ed273 27 user manual guide.
AM/FM/NATURE SOUND
repeatedly to select the desired band
(
AM or FM).
2
Press
NATURE SOUND/PRESET (1 to 5)
where the desired station is stored.
3
Press
VOL/SET + or – to adjust the
volume.
Note
If no station has been preset yet, “Non”
appears on the display. Then the unit returns
to the same state as in step
1.
Selecting a Nature
Sound
This unit includes 5 types of Nature Sounds:
Sea Waves, Birds, Rain, Brook, and Under the Sea.
1
Press
AM/FM/NATURE SOUND
repeatedly to select the Nature Sound.
2
Press the desired
NATURE SOUND/
PRESET (1 to 5).
Icons
Sound type
Sea Waves
Birds
Rain
Brook
Under the Sea
To turn off the Nature Sound, press
ALARM
RESET/OFF.
Note
When other functions are in use, Nature
Sounds are not available.
Setting the alarm
The dual alarm function allows you to set two
alarm programs (
ALARM A and ALARM B).
Sony Icfc1pj Alarm Clock Radio User Manual 41483
The alarm time can be set for each program
and the alarm sound can be selected from “RADIO” (radio), “BUZZ” (buzzer), or “NATURE” (Nature Sound).
Before setting the alarm
Make sure to set the clock. (See “Setting the
clock manually.”)
To set the radio alarm, first preset your
favorite station. (See “To preset radio
stations.”)
1
Press and hold
SET ALARM/ALARM A
(or
B) for more than 2 seconds.
While setting the alarm, “A” (or “B”) flashes
on the display.
2
Press
VOL/SET + or – to select the
desired hour, and press
SNOOZE/
BRIGHTNESS/ENTER.
3
Press
VOL/SET + or – to select the
desired minute, and press
SNOOZE/
BRIGHTNESS/ENTER.
4
Press
VOL/SET + or – to select the
desired alarm period (“WEEKDAY,”
“WEEKEND,” or every day*), and press SNOOZE/BRIGHTNESS/ENTER. * In the case of every day, both
“WEEKDAY” and “WEEKEND” are
displayed.
5
Press
VOL/SET + or – to select the
desired alarm mode (“RADIO,” “BUZZ,”
or “NATURE”), and press
SNOOZE/
BRIGHTNESS/ENTER.
When selecting “RADIO”
Proceed to “
Setting the radio alarm.”
When selecting “BUZZ”
The setting is complete. The buzzer will sound at the set time, gradually increasing in volume. (“A” (or “B”) flashes on the display.)
When selecting “NATURE”
Proceed to “
alarm.”
Setting the radio alarm
6
Press
VOL/SET+ or – to select the AM
band or FM band, and press
SNOOZE/
BRIGHTNESS/ENTER.
7
Press
VOL/SET+ or – (or NATURE
SOUND/PRESET (1 to 5)) to select the
preset number of desired station, and press
SNOOZE/BRIGHTNESS/ENTER.
If no station has been preset yet
The preset number and “Non” appear on the display alternately. In this case, the buzzer will sound at the set time.
8
Press
VOL/SET + or – to adjust the
volume, and press
SNOOZE/
BRIGHTNESS/ENTER.
The setting is complete. The radio will turn
on at the set time, gradually increasing in volume. (“A” (or “B”) flashes on the display.)
Setting the Nature Sound alarm
6
Press
VOL/SET + or – (or NATURE
SOUND/PRESET (1 to 5)) to select the
desired Nature Sound, and press SNOOZE/BRIGHTNESS/ENTER.
7
Press
VOL/SET + or – to adjust the
volume, and press
SNOOZE/
BRIGHTNESS/ENTER.
The setting is complete. The Nature Sound
will sound at the set time, gradually increasing in volume. (“A” (or “B”) flashes on the display.)
To stop the alarm
Press
ALARM RESET/OFF to turn off the
alarm.
The alarm will sound again at the same time
the next weekday or the next weekend.
To doze for a few more minutes
Press
SNOOZE/BRIGHTNESS/ENTER.
The sound turns off, but will automatically
come on again after about 10 minutes. Each time you press
SNOOZE/BRIGHTNESS/
ENTER, the snooze time changes as follows:
The display shows the snooze time for a few
seconds and returns to show the current time. (“A” (or “B”) flashes on the display.)
To deactivate the alarm
Press
SET ALARM/ALARM A (or B).
“A” (or “B”) disappears from the display.
To change an alarm setting
Set the alarm again.
Tips
When the alarm setting is complete, the
alarm time setting is displayed.
If you press and hold SNOOZE/BRIGHTNESS/
ENTER for more than 2 seconds while setting
the alarm, the alarm setting is immediately complete.
Notes
If a second alarm sounds during a first (or
the snooze function is active), the second
alarm takes priority.
If the same alarm time is set for both ALARM
A and ALARM B, ALARM A takes priority.
If no operation is performed while the alarm
is sounding, the alarm will stop after about
60 minutes.
When Automatic DST/summer time
adjustment is set, the alarm sounds as
follows: – If the alarm is set to a time that is
skipped as a result of daylight saving
time starting, the alarm will sound when
daylight saving time is applied.
– If the alarm is set to a time that is
doubled as a result of daylight saving
time ending, the alarm will sound twice.
Notes on the alarm in the event of a
power interruption
In the event of a power interruption, the alarm
functions work until the battery is fully discharged. But certain functions may be affected as follows: The display will disappear. If the alarm sound is set to “RADIO” or
“NATURE,” the buzzer will sound.
If a power interruption occurs while the
alarm is sounding, the buzzer will sound.
If ALARM RESET/OFF is not pressed, the
alarm will sound for about 5 minutes.
If “” appears on the display, the alarm will
not sound in the event of a power
interruption. Replace the battery if “”
appears.
The snooze function will not work.
During a power interruption, the alarm will
sound only once at the set time.
Setting the sleep
timer
You can fall asleep to the radio or Nature
Sound using the sleep timer, which turns off the radio or Nature Sound automatically after a preset duration.
Press
SLEEP while the radio or Nature
Sound is playing.
“SLEEP” appears on the display.
Each time you press
SLEEP, the duration (in
minutes) changes on the display as follows:
The radio or Nature Sound will play for the
duration you set, then shut off. To deactivate the sleep timer, press
SLEEP
repeatedly to set the sleep timer to “OFF.”
To turn off the radio or Nature
Sound before the preset time
Press
ALARM RESET/OFF.
To use both the sleep timer and
alarm
You can fall asleep to the radio or Nature
Sound and also be awakened by the alarm at the preset time.
Set the alarm, then set the sleep timer.
Tip
When you press SLEEP while the sleep timer
is activated, the remaining time appears on
the display.
Note
When the alarm is set to sound during the
sleep timer duration, the sleep timer will be
deactivated automatically when the alarm sounds.
Setting the brightness
of the display
Three levels of brightness are available.
Press
SNOOZE/BRIGHTNESS/ENTER.
Each time you press
SNOOZE/BRIGHTNESS/
ENTER, the brightness of the display changes
as follows:
Tip
You can also set the brightness of the display
to off by pressing and holding
SNOOZE/
BRIGHTNESS/ENTER.
Notes
When the alarm is sounding or the snooze
function is active, the brightness of the
display cannot be changed.
Even if the brightness is set to off, the display
lights at a low brightness level when the
alarm sounds.
Charging a
smartphone
You can charge a smartphone by connecting it
to the unit using a USB cable (not supplied).
Smartphone
USB cable supplied
with the smartphone
Notes
There is no guarantee that this unit can be
used to charge all products that can be
charged via USB.
This unit does not support power feeds
greater than 5 V/1.5 A.
Check the charge status on the smartphone.
If a warning tone sounds, remove the
smartphone from the unit.
The reception sensitivity on the radio may
worsen when charging a smartphone via
USB.
Advertising
Popular Brands
Popular manuals
General information, Getting started, Fm/am clock radio
Advertising
ICF-C1PJ_U2 [US] 4-528-478-
11(2)
NOTES ON LITHIUM BATTERY
Wipe the battery with a dry cloth to assure a
good contact.
Be sure to observe the correct polarity when
installing the battery.
Do not hold the battery with metallic
tweezers, otherwise a short-circuit may
occur.
Do not expose the battery to excessive heat
such as direct sunlight, fire or the like.
If you have any questions or problems
concerning your unit, please consult your nearest Sony dealer.
General information
About the battery as a
backup power source
This unit contains a CR2032 battery as a backup
power source to keep the clock and the alarm operating during a power interruption. (No Power No Problem system)
When to replace the
battery
When the battery is discharged, “
” appears
on the display.
If a power interruption occurs while the battery is discharged, the current time and alarm will be erased.
Note
If “AM 12:00” flashes on the display when the
unit is connected to an AC outlet for the first
time, the battery may be discharged. In this case, consult your nearest Sony dealer.
Replacing the backup
battery
1
Keep the AC plug connected to the
wall outlet, then open the battery
compartment on the bottom of the unit.
Fully loosen
the screw.
Push the tab
and pull up the lid.
2
Remove the old battery by sliding it
out and picking it up.
3
Insert a new battery into the battery
compartment with the
side facing
up.
CR2032
4
Replace the battery compartment lid
and tighten the screw.
5
Press
AM/FM/NATURE SOUND to
remove “” from the display.
Notes
When you replace the battery, do not
disconnect the AC plug from the wall outlet.
Otherwise, the current date and time, alarm, and station presets will be erased.
If the clock is erased while you are replacing
the battery, set the clock again. (See “Setting
the clock manually”)
If the unit will be left unplugged for a long
time, remove the battery to avoid any
damage that may be caused by leakage or corrosion.
Troubleshooting
Should any problems persist after you have
made the following checks, consult your nearest Sony dealer.
The clock flashes “0:00” or “AM 12:00”
after a power interruption.
The battery is discharged. Remove the old
battery and insert a new one.
Unsatisfactory reception
Extend the FM wire antenna fully to increase
reception sensitivity.
Connect the supplied AM loop antenna to
the unit. Rotate the antenna horizontally for
optimum reception.
Do not place the AM loop antenna near the
unit or other AV equipment, as noise may
result.
Keep digital music players or mobile phones
away from the AM loop antenna or the FM
antenna, as this may lead to reception interference.
The alarm does not sound at the preset
alarm time.
Check that “A” or “B” appears on the display.
The radio or Nature Sound alarm is
activated but no sound is emitted at the preset alarm time.
Check the alarm volume setting.
When daylight saving time (summer
time) begins, the clock does not switch to daylight saving time (summer time) automatically.
Make sure the clock is set correctly.
When “Aut On” appears on the display
after pressing and holding
DST for more than
2 seconds, the Automatic DST/summer time
function becomes active.
Specifications
Time display
Switch between the 12-hour system (default)
and the 24-hour system.
Frequency range
Band
Frequency
Channel step
FM
87.5 MHz – 108 MHz
0.1 MHz
AM
530 kHz – 1,710 kHz
10 kHz
Speaker
Approx. 4.0 cm (1 5/8 inches) dia., 8 Ω
Power output: 700 mW (at 10% harmonic distortion)
Power requirements
120 V AC, 60 Hz
For clock back up: 3 V DC, one CR2032 battery
USB power output
USB port (DC OUT 5 V 1.5 A)
Sony Clock Radio Icf C1pj
Nature Sounds
Sea Waves, Birds, Rain, Brook, Under the Sea
Dimensions
Approx. 114.5 mm
104 mm 100.5 mm
(w/h/d) (4 5/8 inches
4 1/8 inches
4 inches) including projecting parts and
controls
Mass
Approx. 595 g (1 lb 5 oz) including CR2032
battery
Supplied accessories
AM loop antenna (1)
Design and specifications are subject to
change without notice.
Before operating the unit, please read this
guide thoroughly and retain it for future reference.
For customers who purchased this
product in the USA
Please register this product on line at
http://www.sony.com/productregistration.
Proper registration will enable us to send
you periodic mailings about new products,
services, and other important
announcements. Registering your product
will also allow us to contact you in the
unlikely event that the product needs
adjustment or modification. Thank you.
Owner’s Record
The model and serial numbers are located on
the bottom of the unit. Record these numbers Nikon forestry pro laser rangefinder specifications user manual online. in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No.
Serial No.
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or
moisture.
To reduce the risk of fire, do not cover the
ventilation of the apparatus with newspapers, tablecloths, curtains, etc. And do not place lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined
space, such as a bookcase or built-in cabinet.
Do not expose batteries or apparatus with
battery-installed to excessive heat such as sunshine, fire or the like.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately.
The unit is not disconnected from the AC
power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.
The nameplate and important information
concerning safety are located on the bottom exterior.
You are cautioned that any changes or
modifications not expressly approved in this manual could void your authority to operate this equipment.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same type.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
The following FCC statement
applies only to the version of
this model manufactured for
sale in the USA. Other versions
Sony Icf C1pj Manual
may not comply with FCC
technical regulations.
NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
— Reorient or relocate the receiving
antenna.
Sony Dual Alarm Clock Radio
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced
radio/TV technician for help.
WARNING
Do not ingest battery, chemical burn
hazard.
This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat. Alarm Clock Radio Kids
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified
by the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
For the state of California, USA
only
Perchlorate Material –special handling may
apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate Perchlorate Material: Lithium battery contains perchlorate
License and Trademark
Notice
No Power No Problem™ is a trademark of Sony
Corporation.
Precautions
Operate the unit on the power sources
specified in “Specifications.”
To disconnect the power cord (mains lead),
pull it out by the plug, not the cord.
Do not leave the unit in a location near a
heat source, such as a radiator or airduct, or
in a place subject to direct sunlight, excessive dust, mechanical vibration, or shock.
Allow adequate air circulation to prevent
internal heat build-up. Do not place the unit
on a surface (a rug, blanket, etc.) or near materials (a curtain) that might block the ventilation holes.
Getting Started
Connecting the AM
loop antenna
The shape and the length of the antenna is
designed to receive AM signals. Do not dismantle or roll up the antenna.
1
Raise the plastic stand and fit the
antenna into the slot of the stand.
Press the
antenna into the stand until it clicks.
Plastic stand
2
Insert the AM antenna connector into
the
AM ANTENNA jack on the unit.
To remove the AM loop
antenna
Push and hold down the tab of the antenna
terminal clamp, and remove the AM loop antenna.
Connecting to an AC
power source
Connect the AC power cord to a wall outlet.
To wall outlet
“month and day” (about 2 seconds)
“year”
(about 2 seconds)
“current EST (Eastern
Standard Time)” appears on the display in turn.
(This unit is preset to the current EST at the factory, and is powered by the back-up battery.)
Setting the clock for
the first time
All you need to do to set the clock for the first
time is select your time zone. If you live in the Eastern Standard Time zone, you do not need to adjust the area setting.
1
Press and hold
TIME ZONE for more
than 2 seconds.
Area number “–5:00” appears on the
display.
2
Press
VOL/SET + or – repeatedly to
select a number as follows:
Area number
Time zone
“–3:30”
Newfoundland Standard
Time
“–4:00”
Atlantic Standard Time
“–5:00”
Eastern Standard Time
(default)
“–6:00”
Central Standard Time
“–7:00”
Mountain Standard Time
“–8:00”
Pacific Standard Time
“–9:00”
Alaska Standard Time
“–10:00”
Hawaii Standard Time
3
Press
SNOOZE/BRIGHTNESS/ENTER
to set.
Note
During shipment and your first use, a clock
error may occur. In this case, refer to “Setting
the clock manually” to set the correct time.
About Automatic DST/
summer time adjustment
This unit automatically adjusts for daylight
saving time (summer time). “DST” automatically appears on the display at the beginning of daylight saving time (summer time), and disappears at the end of daylight saving time (summer time).
Daylight saving time (summer time) begins
at 2:00 AM on the second Sunday of March.
Standard time begins at 2:00 AM on the first
Sunday of November.
Notes
The implementation of DST/summer time
and its beginning/ending date and time are
subject to circumstances and laws in each country/region. Should this interfere with the desired adjustment, cancel the Automatic DST/summer time adjustment and set the clock manually as necessary. Customers living in a country/region that does not use daylight saving time (summer time) should cancel the Automatic DST/summer time adjustment before using the unit.
When Hawaii Standard Time is set, the
default Automatic DST/summer time
adjustment setting is off.
To cancel Automatic DST/
summer time adjustment
The Automatic DST/summer time
adjustment can be canceled.
Press and hold
DST for more than 2
seconds.
“Aut
OFF” appears on the display.
To reactivate Automatic DST/
summer time adjustment
Press and hold
DST for more than 2
seconds.
“Aut
On” appears on the display.
This unit includes a preinstalled Sony Lithium battery (CR2032) as a back-up power source for the clock,
which is preset to EST (Eastern Standard Time) at the factory. This battery is considered part of the product.
This warranty is valid only in the United States.
FM/AM Clock Radio
Operating Instructions
©2014 Sony Corporation Printed in China
4-528-478-
11(2)
ICF-C1PJ
Advertising
Popular Brands
Popular manuals
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |